Offer 372226
EUROPROGETTI EPS 175 L
牌 | 模型 |
---|---|
EUROPROGETTI | EPS 175 L |
EUROPROGETTI EPS 175 L technical details | |
Max Covering Sheet Size | 900x720 mm |
Min Covering Sheet Size | 123x88 mm |
Max Box Width | 415 mm |
Max Box Length | 600 mm |
Max Box Height | 185 mm |
Speed, Subject To Size | up to 34 cycles/minutes (subject to sizes and design) |
Power consumption | |
Floor Space | |
Hs Code | 84439959 HS Codes Classification of Other |
Transport By Truck | |
Transport By Sea | |
优惠详情 | |
年龄 | 2021 |
条件 | Good |
位置 | Europe |
Under power | 是 |
仍在生产中 | 是 |
可能的测试 | 是 |
完成并处于工作状态 | 是 |
可得到 | |
优惠最后更新 | Mon, 15 Apr 2024 10:33:20 +0200 |
描述/机器配置 | |
Automatic Rigid Box Line <> Digital line for the production of rigid, angled, tall and cost saving ‘T shape’ & cross shape covered boxes. <> Very low use, in ‘like new’ condition! <> Equipped with: <> EPQ175SB/1 Automatic Quad Stayer <> - High Pile Feeder for Board Blanks <> - Feeder with non-stop device. <> - Double board blanks warning system with machine stop <> - Board blanks feeding through suckers with lift at the front edge <> - Sliding system with rolls and belts at adjustable speed to eliminate breaking of board blanks <> - Precise location of board blanks under forming block with pushers <> - Precision adjustment of forming block position through brushless motor <> - Large diameter thermo-tape reels located on the side of the machine with an “end-of –reel” <> acoustic signal. Facility to change reel without stopping machine <> - Thermo tape heat-sealing system with adjustable pressure pads on the corners of forming block <> - “Cross-shaped” and “T-shaped” stitching system. <> - Box ejection by cylinder and suction to position the box precisely on conveyor belt <> - Box transport system to the spotter with 2 operating modes <> - Digital display and temperature control of the 4 heat sealing tape anvils <> ALFACEHB5” Automatic Gluing Machine <> - Automatic Glue Viscosity Control Unit <> - Automatic sheet feeder with lifting the rear of the sheet for the insert of papers up to 300 g/m2 <> - Stainless steel, chromed and rectified glue rolls <> - Rollers/belt speed automatic adjustment <> - Vacuum conveyor with running digitally adjustable gap control <> - Servo driven motor on vacuum conveyor with mm by mm variable step control <> - Centralised lubrication <> - Strong aluminium vacuum suction channel with guides for suction conveyor belt <> - Perforated green conveyor belt in polyurethane, with higher suction capacity to the centre <> - Additional vacuum box for small sheets <> - Controlled acceleration and deceleration of conveyor belt, motor driven <> - Auto sheet detection - if glue pickers not lowered, paper will not feed <> - Glue Tank “GTCEC02” with capacity of 70 litres <> - Anti-air bubbles system <> EPS175SB Automatic Spotter <> - Choice of left or right-hand side <> - Suction speed adjustable with inverter <> - Box unloading even without research <> - Paper reading by three optic fibres and hydraulic control unit <> - Mechanical guide unit to control box movement during positioning <> - Simple size change-over <> EPW175SB Automatic Wrapping Machine <> - The wrapper is the Master of the line <> - Possibility of ‘T’ shape wrap for boxes up to 60 mm width <> - Correct ergonomic working height <> - Work cycle controlled by P.L.C - no mechanical cam <> - Possibility to lift box from belt <> - Easy fixing and locking tools <> - Regulating pressing time up to 9,99 seconds <> - Standard or sequential inside turn-in <> - Possibility of inside wrapping up to 70 mm <> - 800 job programs storage <> Accessories: <> - Kit for window box <> - Kit for lateral turn-in up to 80mm <> - Tooling for bottom or lid |